Equipment information

Anritsu MS610A Spectrum analyzer
Manufacturer:
Model:
MS610A
Date:
1985
Category:
Group:
Description:

Information

The MS610A Spectrum Analyzer has a wide frequency range of 10 kHz to 2 GHz, and covers a broad range from the video band to the UHF/VHF band. It is used mainly for spurious response measurement of radio equipment, etc., assembly line adjustment, distortion measurement of various performance elements and circuits (for example, in amplifiers), and broadcast signal panoramic reception and EMI (Electro Magnetic Interference) measurements, etc. The MS610A has multiple functions for these uses: a coupling function, measured level digital display function for efficient measurement, a GP-IB function, which allows simple automation of measurement, and an EMI measurement function with QP (Quasi Peak) detector. The last two are available as options. A tracking Generator (MH680A) is available as a peripheral device for transmission measurement.

show more

User Manual
Manual Type:
User Manual
Pages:
64
Size:
7.42 Mbytes (7781321 Bytes)
Language:
english
Revision:
Manual-ID:
Date:
Quality:
Scanned document, all readable.
Upload date:
2014 05 02
MD5:
88b2757f227a64690b7869f56ba9e5c8
Downloads:
1253

Information

SECTION 1 GENERAL ... 1-1 4 SECTION 2 COMPOSITION AND SPECIFICATIONS ... 2-1 2.1 Composition ... 2-1 2.2 Soecifications ... 2-1 2.3 Peripheral Devices and Accessories ... 2-5 2.3.1 MH680A Tracking Generator ... 2-5 2.3.2 MH648A Preamplifier ... 2-6 2.3.3 Antenna ... 2-7 2.3.4 Packet He Personal Technical Computer .. 2-7 2.3.5 Accessories ... 2-8 SECTION 3 PRINCIPLES OF OPERATION ... 3-1 3.1 Introduction ... 3-1 3.2 Frequency Conversion Circuit ... 3-1 3.3 IF Circuit ... 3-2 3.4 Detection and Video Circuits ... 3-3 3.5 Sawtooth Generator and Local Oscillator Control Circuit ... 3-3 3.6 Controller ... 3-4 SECTION 4 PREPARATIONS ... 4-1 4.' Safety Measures ... 4-1 4.2 Power-ON ... 4-2 4.3 Gain Calibration ... 4-3 4.4 Frequency Display ZERO Calibration ... 4-4 4.5 TRACE ROTATION and V. POSITION Adjustment . . 4-4 SECTION 5 OPERATION ... 5-1 5.1 Description of Front and Rear Panels ... 5-1 5.2 Description of Controls ... 5-5 5.2.1 FREQUENCY ... 5-5 (1) COARSE - FINE dial ... 5-5 (2) START FREQ and CENTER FREQ ... 5-6 (3) FREQ ZERO ADJ ... 5-6 5.2.2 MODE ... 5-7 (1) DATA ... 5-7 (2) REFERENCE LEVEL ... 5-7 (3) MARKER LEVEL ... 5-8 (4) FREQ SPAN ... 5-9 (5) INPUT ATTEN ... 5-9 (6) RBW ... 5-10 (7) SWEEP TIME ... 5-11 5.2.3 COUPLED TO SPAN ... 5-12 5.2.4 COUPLED TO REF ... 5-14 5.2.5 VIDEO Filter ... 5-15 5.2.6 SCALE ... 5-16 5.2.7 TRIG ... 5-17 5.2.8 DISPLAY UNCAL ... 5-18 5.2.S GAIN ADJ ... 5-18 5.2.10 INTENSITY ... 5-19 5.2.11 GP-IB ... 5-19 5.2.12 REFERENCE LEVEL (rear panel) ... 5-20 SECTION 6 MEASUREMENT ... ' ... 6-1 6.1 Typical Measurement ... 6-1 (1) General measurement method ... 6-1 (2) Improvement of frequency measurement accuracy ... 6-2 6.2 Modulated Wave Measurement ... 6-2 (1) Measurement Procedure ... 6-2 (2) AM wave measurement ... 6-3 (3) Measurement of AM wave when modulation frequency is low ... 6-4 (4) FM wave measurement ... 6-5 (5) PAM wave measurement ... 6-6 6.3 Spurious measurement ... 6-7 (1) Harmonic distortion measurement ... 6-7 (2) Inter modulation product measurement .. 6-9 (3) Random spurious signal measurement ... 6-9 (4) Spectrum purity measurement ... 6-9 6.4 Field Strength Measurement ... 6-10 (1) Measurement in dBu units ... 6-10 (2) Direct reading measurement of field strength using the specified antenna ... 6-10 (3) Antenna coefficient display ... 6-11 SECTION 7 DAILY MAINTENANCE AND STORAGE ... 7-1 7.1 Daily Maintenance ... 7-1 7.2 Storage ... 7-1 7.2.1 Storage Precautions ... 7-1 7.2.2 Recommended Storage Conditions ... 7-2 APPENDIX BLOCK DIAGRAM ... A-l

show more