Informacje o sprzęcie

Quadtech Inc. 1320 Zasilanie
Producent:
Quadtech Inc.
Modelu: 1320
Data: 2001
Kategorii: Przyrządy pomiarowe
Grupa: Zasilanie
Opis: Bias Current Source
Informacje:

Te Podręczniki są dostępne dla powyższego urządzenia:

Typ instrukcji: Instrukcja obsługi QuadTech-8631-Manual-Page-1-Picture
Stron: 81
Rozmiar: 464.45 Kbytes (475592 Bytes)
Język: Angielski
Zmiana:
Podręcznik numer: 150414/A2
Data: 01 marzec 2001
Jakość: Dokument elektroniczny, bez skanowania, bardzo dobrze czytelne.
Data wysłania:
MD5: 84fc697e6c02daed635ff9eb2c3db84e
Pliki do pobrania: 58 od 29 styczeń 2017
Informacje:

Warranty ... 5 Specifications ... 7 Accessories ... 9 Safety Precautions ... 11 Condensed Operating Instructions ... 13 Introduction - Section 1 1.1 Unpacking and Inspection ... 15 1.2 Product Overview ... 15 1.3 Controls and Indicators ... 16 1.3.1 Front Panel Controls and Indicators ... 16 1.3.2 Rear Panel Controls and Connectors ... 19 1.4 Installation ... 20 1.4.1 Dimensions ... 20 1.4.2 Instrument Positioning ... 20 1.4.3 Power Requirements ... 21 1.4.4 Safety Inspection ... 22 Operation - Section 2 2.1 Terms and Conventions ... 23 2.2 System Parameters ... 26 2.2.1 Shift ... 27 2.2.2 I/F (Interface) ... 27 2.2.3 I (Current) ... 28 2.2.4 Mode ... 29 2.2.5 Address ... 34 2.2.6 Clock ... 34 2.2.7 Timer ... 35 2.2.8 Delay Time ... 36 2.2.9 Step Number ... 37 2.2.10 Loop ... 38 2.2.11 Local ... 38 2.2.12 Prog/Esc ... 39 2.2.13 Store ... 40 2.2.14 Recall ... 41 2.2.15 Clear ... 41 2.2.16 B.S. (Backspace) ... 42 2.2.17 Enter ... 42 2.2.18 DCV Display ... 42 2.2.19 BIAS/DCR ... 43 2.2.20 FWD/REV ... 43 2.3 Start-Up ... 44 2.4 Zero Function ... 44 2.5 Connection to Device Under Test ... 45 2.5.1 Connection to Single DUT ... 45 2.5.2 Connection to 1750 Digibridge ... 46 2.5.3 Connection to 7000 Series Precision LCR Meter ... 48 2.5.4 Connection to 1900 Series Precision Impedance Meter ... 49 2.6 Measurement Procedure ... 56 2.6.1 Bias Current source ... 56 2.6.1.1 Programming Example #1: Single Current Test ... 59 2.6.1.2 Programming Example #2: Multi-Point Current Test ... 60 2.6.1.3 Programming Example #3: Multi-Point Current Loop ... 61 2.6.2 DCR (DC Resistance) Measurement ... 62 2.6.3 Error Messages ... 63 Interface – Section 3 3.1 IEEE-488 Interface ... 66 3.1.1 Pin Configuration ... 66 3.1.2 Address Change ... 67 3.1.3 Interface Codes ... 67 3.1.4 Interface Bus & Messages ... 68 3.1.5 Listener Functions ... 69 3.1.5.1 Common Commands ... 69 3.1.5.2 System Commands ... 70 3.2 Handler Interface ... 71 3.3 1320S Bias Current source Slave ... 73 3.4.1 Front Panel Controls and Indicators ... 74 3.4.2 Rear Panel Controls and Connectors ... 75 3.4.3 Slave Interface Pin Configuration ... 76 3.4.4 Slave Connection to 1320 ... 76 Service & Calibration - Section 4 4.1 General ... ... 79 4.2 Instrument Return ... ... 79 4.3 Calibration ... 79 4.3.1 Equipment Required ... 80 4.3.2 1320 Calibration (MASTER) ... 80 4.3.2.1 Sink Board Current Adjustment ... 80 4.3.2.2 DCR Board Voltage Adjustment ... 83 4.3.3 1320S Calibration (SLAVE) ... 84

QuadTech-8631-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image
Powered by Commentics