Apparatuur informatie

Keithley 224 Stroombron
Fabrikant:
Model:
224
Datum:
1984
Categorie:
Groep:
Omschrijving:
Programmable Current Source

Informatie

The model 224 is a programmable Current source with full range current output of 20,uA to 101 mA. The smallest step of output current is 5nA. The model 224 has a selectable voltage compliance of up to 105V in IV increments. The value of output current can be modified in two ways: manually or automatically. The automatically modified current value is incremented or decremented by the programmed rate. The time button allows the modification of the programmed auto increment/decrement rate. The control of the current value modification can be activated by an external trigger pulse applied to the EXTERNAL TRIGGER INPUT. At the completion of the current value modification (each digit) the Model 224 outputs a pulse that has the specifications shown in Figure 2-5. This pulse can be used to trigger another instrument (printer, DMM, controller, etc.1 to start its programmed task. With the Model 2243 IEEE-488 Interface option installed, the model 224 can be used with any measurement system that uses ?he IEEE-488 bus. For detailed operating instructions of the Model 2243 IEEE-488 Interface option, refer to the Model 2243 Instruction Manual

toon meer

Gebruikershandleiding
Handleidingen type:
Gebruikershandleiding
Pagina’s:
40
Grootte:
477.84 Kbytes (489304 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
Kwaliteit:
Gescande document, lezen deels slecht, deels niet leesbaar.
Upload datum:
07 maart 2014
MD5:
6fafc31921aa96b21c4f6b61686d5b69
Downloads:
536

Informatie

Quick Reference Guide

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
75
Grootte:
5.85 Mbytes (6130409 Bytes)
Taal:
english
Herziening:
Fifth Printing
Handleidingen-ID:
224-901-01
Datum:
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
20 mei 2012
MD5:
996e2d118d061fc1f450859969532625
Downloads:
926

Informatie

Para. Title Page SECTION 1 — GENERAL INFORMATION 1.1 Introduction ... 1-1 1.2 Features ... 1-1 1.3 Warranty Information ... 1-1 1.4 Manual Addenda ... 1-1 1.5 Safety Symbols and Terms ... 1-1 1.6 Unpacking and Inspection ... 1-1 1.7 Repacking for Shipment ... 1-2 1.8 Specifications ... 1-2 1.9 Accessories ... 1-2 SECTION 2 — OPERATION 2.1 Introduction ... 2-1 2.2 Preparation for Use ... 2-1 2.2.1 Correct Line Voltage ... 2-1 2.2.2 Power Up ... 2-1 2.2.3 Warm Up ... 2-1 2.3 Operating lnstructions ... 2-1 2.3.1 Environmental Conditions ... 2-1 2.3.2 Front Panel Controls ... 2-1 2.3.3 Rear Panel Description ... 2-1 2.3.4 Output Connector ... 2-6 2.3.5 Inductive Loads ... 2-6 2.3.6 Response Time ... 2-6 2.3.7 General Operating Procedure ... 2-6 2.3.8 Front Panel Messages ... 2-7 2.3.9 Examples of Operation ... 2-7 2.4 Applications ... 2-12 2.4.1 Calibration ... 2-12 2.4.2 Resistivity Measurements ... 2-12 2.4.3 Diode Characterization ... 2-13 2.4.4 Low Resistance “Lindeck” Measurements ... 2-14 2.5 Detailed Front Panel Controls Description ... 2-14 2.6 Detailed Rear Panel Description ... 2-l 5 SECTION 3 — PERFORMANCE VERIFICATION 3.1 Introduction ... 3-1 3.2 Environmental Conditions ... 3-1 3.3 Recommended Test Equipment ... 3-1 3.4 Initial Conditions ... 3-1 3.5 Performance Verification Procedure ... 3-1 3.5.1 100mA to 1mA Range Verification ... 3-1 3.5.2 100μA and 10μA Range Verification ... 3-2 SECTION 4 — THEORY OF OPERATION 4.1 Introduction ... 4-1 4.2 Block Diagrams ... 4-1 4.3 Power Supply ... 4-1 4.4 Analog Board ... 4-1 4.5 Digital Board (Microcomputer) ... 4-2 Para. 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.7.1 5.7.2 5.7.3 5.7.4 5.8 5.8.1 6.1 6.2 6.3 6.4 6.5 Title Page SECTION 5-MAINTENANCE Introduction ... 5-l FuseReplacement ... 5-l LineVoltageSelection ... 5-1 Disassembly ... ~ ... 5-2 FanFilterMaintenance ... 5-2 Special Handling of Static Sensitive Devices ... 52 Calibration ... 5-4 RecommendedTestEquipment ... 5-4 Environmental Conditions. ... 5-4 Warmup.. ... 5-4 Calibration Adjustments ... 5-4 Troubleshooting ... 5-5 DigitalSelfTest ... 5-5 SECTION 6-REPLACEABLE PARTS Introduction ... 6-l PartsList ... 6-l Orderinglnformation ... 6-l FactoryService.. ... 6-l Schematic Diagrams and Component Location Drawings ... 6-1

toon meer

Add Comment

* Required information
1000
Captcha Image

Comments

No comments yet. Be the first!