Apparatuur informatie

Kern & Sohn GmbH DS16 Weegschaal
Fabrikant:
Kern & Sohn GmbH
Model: DS16
Datum: 2006
Categorie: Medische en biomedische apparatuur
Groep: Weegschaal
Beschrijving: Precision Balance
Informatie:

Deze handboeken zijn beschikbaar voor de bovengenoemde apparatuur:

Manueel de Type: Servicehandboek Kern-10439-Manual-Page-1-Picture
Pagina 's: 22
Grootte: 1.22 Mbytes (1277284 Bytes)
Taal: Engels
Herziening: 5.1
Handleiding-ID/Number: 572/573/KB/DS/FKB-BA-defsi-0651
Datum: 01 mei 2006
Kwaliteit: Elektronisch document, geen scan, zeer goed leesbaar.
Uploaden datum:
MD5: 4c40ccd3a88248d5c04e254c4c0976ed
Downloads: 266 Sinds 24 februari 2018
Informatie:

1 MODE - MENUE __________________________________________________________ 26 2 Technical data _____________________________________________________________ 27 2.1 KERN 572 __________________________________________________________________ 27 2.2 KERN 573 __________________________________________________________________ 28 2.3 KERN KB __________________________________________________________________ 29 2.4 KERN FKB _________________________________________________________________ 29 2.5 KERN DS ___________________________________________________________________ 30 3 Fundamental information (general) ___________________________________________ 31 3.1 Intended use_________________________________________________________________ 31 3.2 Inappropriate use ____________________________________________________________ 31 3.3 Guarantee __________________________________________________________________ 31 3.4 Monitoring the test substances__________________________________________________ 31 4 Fundamental safety information ______________________________________________ 32 4.1 Observe the information in the operating instructions ______________________________ 32 4.2 Staff training ________________________________________________________________ 32 5 Transport and storage _______________________________________________________ 32 5.1 Acceptance check ____________________________________________________________ 32 5.2 Packaging___________________________________________________________________ 32 6 Unpacking, installation and commissioning _____________________________________ 32 6.1 Place of installation, place of use ________________________________________________ 32 6.2 Unpacking __________________________________________________________________ 33 6.2.1 Installation _______________________________________________________________________ 33 6.3 Mains supply ________________________________________________________________ 33 6.4 Connecting peripheral equipment _______________________________________________ 33 6.5 Initial start-up _______________________________________________________________ 33 6.6 Adjustment _________________________________________________________________ 33 6.7 Adjusting ___________________________________________________________________ 33 6.7.1 Adjusting for verification (KERN 573) _________________________________________________ 34 6.8 Verification _________________________________________________________________ 34 7 Operation _________________________________________________________________ 35 7.1 Display control panel _________________________________________________________ 35 7.2 Operation ___________________________________________________________________ 36 7.2.1 Weighing with Tare ________________________________________________________________ 36 7.2.2 Count – Selection Preference Piece ____________________________________________________ 36 7.2.3 Percent % ________________________________________________________________________ 36 7.2.4 Formula Weighing _________________________________________________________________ 36 7.2.5 Tolerance Weighing ________________________________________________________________ 36 7.2.6 Adjust ___________________________________________________________________________ 38 7.2.7 Preselect Tare _____________________________________________________________________ 38 7.2.8 Auto Tare ________________________________________________________________________ 38 7.2.9 Speed ___________________________________________________________________________ 38 7.2.10 Auto Off _______________________________________________________________________ 38 7.2.11 Variable Factor__________________________________________________________________ 38 7.2.12 Preselect Unit ___________________________________________________________________ 38 7.3 Interface RS 232 C ___________________________________________________________ 40 7.4 RS 232 C Data output via interface RS 232 C _____________________________________ 40 7.4.1 There are 4 methods for the data output via RS 232 C______________________________________ 40 7.4.2 Description of the data transfer________________________________________________________ 41 7.4.3 Numerator ________________________________________________________________________ 41 7.5 Printer _____________________________________________________________________ 41 7.6 Underfloor weighing __________________________________________________________ 41 8 Maintenance, upkeep, disposal________________________________________________ 42 8.1 Cleaning ____________________________________________________________________ 42 8.2 Maintenance, upkeep _________________________________________________________ 42 8.3 Disposal ____________________________________________________________________ 42 9 Troubleshooting ___________________________________________________________ 42 10 Declaration of conformity__________________________________________________ 43

Kern-10439-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image
Powered by Commentics