Equipment information
Keithley 617 Digital multimeter
Manufacturer:
No picture available!
Maybe you can upload a pic for the
Keithley 617 ?
If you have any other manuals for the
Keithley 617 you can upload the files here .
Model:
617
Date:
1984
Category:
Group:
Description:
Programmable Electrometer
Information
The Keithley model 617 Programmable Electrometer is a
highly sensitive instrument designed to measure voltage,
current,
charge, and resistance. Two forms of resistance
measurements are included in the standard configuration: a
constant current method, and a constant voltage method that
uses a built in Voltage Source for greater sensitivity. The
measuring range of the model 617 is between 1OpV and 200V
for voltage measurements, O.lfA and 2OmA in the current
mode, O.ln and 200GO (up to 1OlQ using the built in voltage
source), and lOfC and 20°C in the coulombs mode. The very
high input impedance and extremely low input offset current
allow accurate measurement in situations where many other
instruments would have detrimental effects on the circuit being
measured. A 4% digit display and standard IEEE-488 Interface
give the user easy access to instrument data.
1.2 FEATURES
Some important model 617 features include:
4½ Digit Display-An easy to read front panel LED display
includes a 4½ digit mantissa plus a two-digit alpha or
numeric exponent.
Autoranging-Included for all functions and ranges.
Digital Calibration-The instrument may be digitally
calibrated from the front panel or over the IEEE-488 bus.
l Zero Correct-A front panel zero correct control allows the
user to cancel any offsets.
Baseline Suppression-One button suppression of a
baseline reading is available from the front panel or over the
IEEE-488 bus.
One-shot Triggering-A front panel control for triggering
one-shot readings from the front panel is included.
Isolated IOOV Voltage Source-A built in 1OOV scwrce is
isolated from the electrometer section. The Voltage Source is
programmable in 50mV steps.
Selectable Guarding-A selectable driven cable guard is included
to optimize speed.
Standard IEEE-488 Interface-The Interface allows full bus
programmable operation of the model 617.
Analog Outputs-Both preamp and 2V full range analog
outputs are included on the rear panel.
100~Point Data Store-An internal buffer that can store
up to 100 readings is accessible from either the front panel
or over the IEEE-488 bus.
Minimum and maximum data points can be stored and are
accessible from the front panel or over the IEEE-488 bus.
Manual Type:
Service and User Manual
Pages:
183
Size:
9.71 Mbytes (10179386 Bytes)
Language:
english
Revision:
G
Manual-ID:
617-901-01
Date:
Quality:
Scanned document, all readable.
Upload date:
2014 03 01
MD5:
0475ea639ca4d08912c0492eed431fb2
Downloads:
3151
Information
G E N E R A L ... .
S P E C I F I C A T I O N S ... .
A C C E S S O R I E S ... .
P R E V E N T I V E M A I N T E N A N C E ... .
C I R C U I T D E S C R I P T I O N ... .
C A L I B R A T I O N ... .
6-l. Calibration Interval ... .
6-2. Test Equipment Required. ... .
6-3. Preliminary Procedure. ... .
6-4. Preliminary Control Settings ... .
6-5. Initial Starting Procedure. ... .
7,
8*
Q*
S E M I C O N D U C T O R L E A D
C O N F I G U R A T I O N S ... 28
E L E C T R I C A L P A R T S A R R A N G E M E N T
< W I T H A D J U S T M E N T L O C A T I O N S ) ... 29
ELECTRICAL PARTS LIST ... 32
4
5
a
9
10
14
14
1 4
14
15
15
10, B L O C K DIAGRAM ... 51
11, W I R I N G DIAGRAM ... 52
12, S C H E M A T I C DIAGRAMS ... 53
13* MECHANICALPARTZ-LiST&EXPLODED
VIEW ... 69
14, E X T E R N A L V I E W S ... 74