Informations de l’équipement

Keithley 7999-6 Interface
Fabricant:
Keithley
Modèle: 7999-6
Date: 2001
Catégorie: Mètres
Groupe: Interface
Description: GPIB RF Relay Unit
Informations:

The Model 7999-6 is an IEEE-488 controlled, single or dual, 4 or 6 pole, 19-inch rack mounted relay unit. Additional features of the Model 7999-6 are as follows: • N-type bulkhead connectors (insulated) • +24VDC power connections • LED indicators for error, power, and relay status • Operating range to 4GHz (relay dependent) • Can be upgraded from 4-pole to 6-pole relays

Ces manuels sont disponibles pour les équipements ci-dessus :

Type manuel: Service et Manuel de l'utilisateur Keithley-5543-Manual-Page-1-Picture
Pages: 87
Taille: 1.40 Mbytes (1465105 Bytes)
Langue: Anglais
Révision: A
Numéro d’identification: 7999-6-901-01
Date: avril 2001
Qualité: Électronique de documents, numérisation sans, bien lisible.
Télécharger date:
MD5: eda9430778a16daf86eaac26278b6410
Téléchargements: 269 depuis 02 mars 2014
Informations:

1 General Information Introduction ... 1-2 Feature overview ... 1-2 Warranty information ... 1-2 Manual addenda ... 1-2 Safety symbols and terms ... 1-3 Specifications ... 1-3 Unpacking and inspection ... 1-3 Inspection for damage ... 1-3 Handling precautions ... 1-3 Shipment contents ... 1-4 Instruction manual ... 1-4 Repacking for shipment ... 1-4 Connections ... 1-4 2 Connections Introduction ... 2-2 Handling precautions ... 2-2 Configuration ... 2-2 Layout ... 2-2 Simplified schematic ... 2-4 Connections ... 2-5 GPIB control connection ... 2-5 Power connector ... 2-8 3 Operation Introduction ... 3-2 Maximum signal considerations ... 3-2 Bus operation (GPIB) ... 3-3 Bus connections ... 3-3 Primary address ... 3-3 Programming syntax ... 3-3 Response messages ... 3-7 Status model ... 3-8 Event register sets ... 3-10 Enable registers ... 3-11 Queues ... 3-11 Status byte and SRQ ... 3-13 Service request enable register ... 3-14 Serial polling and SRQ ... 3-15 Clearing registers and queues ... 3-16 Programming enable registers ... 3-17 Reading registers ... 3-17 Common commands ... 3-18 GPIB commands ... 3-26 ROUTe commands ... 3-26 :CLOSe ... 3-28 :CONFigure ... 3-29 STATus commands ... 3-30 :QUEue ... 3-30 SYSTem commands ... 3-32 Manual operation ... 3-34 Switching considerations ... 3-35 Connector integrity ... 3-35 Voltage Standing Wave Ratio ... 3-35 Path isolation ... 3-36 Insertion loss ... 3-36 RFI/EMI ... 3-36 Errors ... 3-37 4 Service Information Introduction ... 4-2 Handling and cleaning precautions ... 4-2 Handling precautions ... 4-2 Card and connector cleaning ... 4-2 Performance verification ... 4-3 Environmental conditions ... 4-3 Recommended equipment ... 4-3 Channel resistance tests ... 4-3 Replacing components ... 4-4 Replacement parts ... 4-4 Replacement precautions ... 4-5 Soldering considerations ... 4-5 Relay replacement ... 4-5 Circuit board removal ... 4-8 GPIB address ... 4-8 5 Replaceable Parts Introduction ... 5-2 Parts list ... 5-2 Ordering information ... 5-2 Factory service ... 5-2 Component layout ... 5-2

Keithley-5543-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image