Equipment information

Philips PM 2811 Power supply
Manufacturer:
Model:
PM 2811
Date:
1992
Category:
Group:
Description:
Programmable Power Supply
Service Manual
Manual Type:
Service Manual
Pages:
28
Size:
1.35 Mbytes (1417285 Bytes)
Language:
english
Revision:
Manual-ID:
4822 872 80169 and/or 920305
Date:
Quality:
Scanned document, all readable.
Upload date:
21 November 2008
MD5:
00b780e20f2b29a5641b6317e3ef07d8
Downloads:
5709

Information

Info only for the Programming Card

show more

Service Manual
Manual Type:
Service Manual
Pages:
66
Size:
17.16 Mbytes (17988714 Bytes)
Language:
english
Revision:
Manual-ID:
4822 872 85004
Date:
01 December 1991
Quality:
Scanned document, all readable.
Upload date:
31 July 2020
MD5:
02436219453c5e5318fcd4d1233de850
Downloads:
944

Information

1 SAFETY INSTRUCTIONS ... 1-1 1.1 INTRODUCTION ... 1-1 1.2 SAFETY PRECAUTIONS ... 1-1 1.3 CAUTION AND WARNING STATEMENTS ... 1-1 1.4 SYMBOLS ... 1-1 1.5 IMPAIRED SAFETY ... 1-2 1.6 GENERAL SAFETY INFORMATION ... 1-2 2 GENERAL INFORMATION ... 2-1 2.1 CHARACTERISTICS ... 2-1 2.1.1 Performance Characteristics ... 2-1 2.1.2 Environmental Characteristics ... 2-1 2.1.3 Mechanical requirements ... 2-1 2.1.4 Instrument performance ... 2-2 2.1.4.1 Output channel 30V/10A/60W performance ... 2-2 2.1.4.2 Output channel 60V/5A/60Wperformance ... 2-4 2.1.4.3 Output channel 60V/10AJ120Wperformance ... 2-5 2.1.5 Safety characteristics ... 2-7 2.1.6 Dimensions and weight ... 2-8 2.1.7 Mains Supply Conditions ... 2-8 2.2 INTERFERENCES ... 2-8 2.2.1 Electromagnetic interference ... 2-8 2.2.2 Frequency interference ... 2-8 3 CIRCUIT DESCRIPTIONS ... 3-1 3.1 DESCRIPTION OF EACH CIRCUIT SECTION ... 3-1 3.1.1 CPU PCB, unit A1 ... 3-1 3.1.2 DISPLAY KEYBOARD PCB, unit A2 ... 3-5 3.1.3 AD-DA PCB, unit A3 ... 3-5 3.1.4 Output on the front panel ... 3-9 3.1.5 Input module ... 3-10 3.1.5.1 Setting the power voltage ... 3-10 4 PERFORMANCE VERIFICATION PROCEDURES ... 4-1 4.1 GENERAL INFORMATION ... 4-1 4.2 RECOMMENDED TEST EQUIPMENT ... 4-1 5 DISASSEMBLING THE INSTRUMENT ... 5-1 5.1 GENERAL INFORMATION ... 5-1 5.2 REMOVING THE COVER ... 5-1 5.3 DISASSEMBLING THE INSTRUMENT ... 5-1 5.4 REASSEMBLING THE INSTRUMENT ... 5-2 6 CALIBRATION ADJUSTMENT PROCEDURE ... 6-1 6.1 GENERAL INFORMATION ... 6-1 6.1.1 Recommended test equipment for local calibration ... 6-1 6.1.2 Recommended test equipment for remote calibration ... 6-1 6.2 CALIBRATION PROCEDURES ... 6-1 6.2.1 Local calibration procedure ... 6-1 6.2.2 Remote calibration procedure ... 6-4 7 CORRECTIVE MAINTENANCE PROCEDURES ... 7-1 7.1 HARDWARE-ERROR MESSAGES ... 7-1 7.2 TROUBLESHOOTING ... 7-2 7.2.1 Introduction ... 7-2 7.2.2 CPU PCB ... 7-2 7.2.3 AD-DA PCB ... 7-3 7.3 REPLACEMENTS ... 7-3 7.3.1 Standard parts ... 7-3 7.3.2 Special parts ... 7-4 7.3.3 Transistors and integrated circuits ... 7-4 7.4 RECALIBRATION AFTER REPAIR ... 7-4 7.5 INSTRUMENT REPACKING ... 7-4 8 SAFETY INSPECTION AND TESTS AFTER REPAIR AND MAINTENANCE IN THE PRIMARY CIRCUIT ... 8-1 8.1 GENERAL DIRECTIONS ... 8-1 8.2 SAFETY COMPONENTS ... 8-1 8.3 CHECKING PROTECTIVE GROUND ... 8-1 8.4 CHECKING INSULATION RESISTANCE ... 8-1 8.5 CHECKING LEAKAGE CURRENT ... 8-1 8.6 VOLTAGE TEST ... 8-1 9 PARTS LIST ... 9-1 10 WIRING DIAGRAM 10-1

show more

Add Comment

* Required information
1000
Captcha Image

Comments

No comments yet. Be the first!