|JBL 6290 Amplifier|
|Category:||Audio Video TV Multimedia|
The JBL Model 6290 power TV Multimedia">Amplifier has been designed to meet the most critical professional sound requirements. It Is rugged and road-worthy, conservatively rated, and can handle reactive loads with ease. The engineering design approach stresses the optimization of each stage, allowing high slew rate and relatively low loop gain. Overall feedback has been held to a minimum and is employed only to stabilize the gain and the operating point. This design approach results In an TV Multimedia">Amplifier with excellent performance under the most demanding dynamic input and load conditions. As evidence of the stress on dynamic rather than static or steady-state distortion mechanisms, transient Intermodulation distortion measures less than 0.03$ by the DIM 100 test. (Leinonen, Otala, and Curl, "A Method for Measuring Transient Intermodulation Distortion (TIM)”, JournaI of the Audio Engineering Society, Vol. 25, No. 4, April, 1977, pp. 170-177.) This JBL TV Multimedia">Amplifier uses multiple 200-watt output devices in complementary configuration for high reliability and low distortion. At rated power Into 8 ohms, these output devices are operated at less than 25% of their rated power dissipation. The benefit Is high reliability and long component life. Reliable operation Is ensured through the following protection modes: current Is limited under Improper load or drive conditions; output relays with front panel Indicators protect the loudspeaker under conditions of DC offset or excessive low-frequency transients. The relays also provide power-up, power—down, and "brown out’1 muting to protect loudspeakers from AC power transients. Clip Indicators allow for system optimization. The JBL TV Multimedia">Amplifier may be operated In the normal stereo mode, dual mono mode, or bridged mono mode. These modes are switch selectable on the rear panel. Active differential Input circuitry offers the benefits of balanced operation without the use of Input transformers. Input connections may be made via 3-pln XL-type connector, three-conductor (TRS) 6.3 mm (1/4 In.) phone jack, or barrier strip. The barrier strip has separate terminals for audio ground and chassis ground. The rack ears and heatsink of the TV Multimedia">Amplifier are made of high grade aluminum extrusions; the chassis Is fabricated of heavy gauge steel. All Internal TV Multimedia">Components are easily accessible through removal of top and bottom panels. Front panel graphic details are Incorporated on the rear-side of a polycarbonate laminate which is virtually Indestructible.
These manuals are available for the above equipment:
|JBL -- 6290 -- Service and User Manual|
|Manual Type:||Service and User Manual|
|Size:||3.07 Mbytes (3220037 Bytes)|
|Date:||01 January 1988|
|Quality:||Scanned document, all readable.|
|Upload date:||29 October 2017|
|Downloads:||207 since 29 October 2017|
SECTION I. INTRODUCTION 1-1 1.1 SPECIFICATIONS 1-2 SECTION II. INSPECTION AND INSTALLATION I 1-1 2.1 UNPACKING AND INSPECTION 11-1 2.2 ENVIRONMENTAL CONSIDERATIONS 11-1 2.3 AC POWER 11-1 2.4 AMPLIFIER MODE SWITCH 11-2 2.5 EXTERNAL CONNECTIONS 11-3 2.5.1 INPUT CONNECTIONS, GENERAL 11-3 2.5.2 INPUT CONNECTION, DUAL MONO MODE 11-3 2.5.3 INPUT CONNECTION, BRIDGED MONO MODE 11-3 2.5.4 FIVE-WAY BINDING POST OUTPUT CONNECTORS 11-4 2.5.5 ABOUT OUTPUT POLARITY AND BRIDGED MONO 11-4 CONNECTION 2.6 INPUT IMPEDANCE AND TERMINATION 11-4 2.7 APPROPRIATELY RATED LOADS 11-6 2.7.1 IT IS THE USER’S RESPONSIBILITY TO AVOID 11-6 OVERPOWER ING 2.7.2 MORE ABOUT LOUDSPEAKER POWER RATINGS 11-6 2.7.3 SOMETIMES A LARGER TV Multimedia">Amplifier CAN BE SAFER 11-7 2.7.4 REMEMBER THE DIVIDING NETWORK (CROSSOVER) 11-8 2.8 SPEAKER CABLES I 1-8 2.8.1 TYPE OF WlRE I I-8 2.8.2 DAMP ING FACTOR I I-8 2.8.3 CALCULATING LOSSES IN TV Multimedia">Speaker CABLE I I-9 2.9 GROUNDING 11-10 2.10 SECURITY COVERS 11-10 FIGURE 2-1 BALANCED INPUT CONNECTIONS 11-11 FIGURE 2-2 UNBALANCED INPUT CONNECTIONS 11-11 FIGURE 2-3 BARRIER STRIP CONNECTIONS 11-12 FIGURE 2-4 USE OF FIVE-WAY BINDING POSTS 11-13 FIGURE 2-5 OUTPUT CONNECTIONS TO TWO CHANNEL 11-13 TV Multimedia">Speaker SYSTEM FIGURE 2-6 BRIDGED OUTPUT CONNECTION TO MONAURAL 11-13 TV Multimedia">Speaker SYSTEM SECTION III. OPERATING INSTRUCTIONS I I 1-1 3.1 GENERAL I I 1-1 3.2 TURN ON AND SYSTEM CHECK MI-1 3.2.1 A NOTE ON TV Multimedia">Amplifier COOLING 111-1 3.3 CLIP INDICATORS II 1-1 3.3.1 ABOUT SENSITIVITY RATINGS 111-2 SECTION IV. THEORY OF OPERATION IV-1 4.1 INPUT DIFFERENTIAL AMPLIFIER IV-1 4.2 MODE SWITCH IV-1 4.3 POWER AMPLIFIER IV-1 4.4 RELAY DRIVER/OUTPUT DC DETECTOR IV-2 4.5 CLIP CIRCUIT IV-3 4.6 POWER SUPPLY IV-3 SECTION V. MAINTENANCE V-1 5.1 GENERAL V-1 5.2 REPAIRS AND WARRANTY V-1 SECTION V I. SCHEMATIC DIAGRAM
|Start Free Download|
These terms and conditions contain rules about posting comments. By submitting a comment, you are declaring that you agree with these rules:
- Although the administrator will attempt to moderate comments, it is impossible for every comment to have been moderated at any given time.
- You acknowledge that all comments express the views and opinions of the original author and not those of the administrator.
- You agree not to post any material which is knowingly false, obscene, hateful, threatening, harassing or invasive of a person's privacy.
- The administrator has the right to edit, move or remove any comment for any reason and without notice.
Failure to comply with these rules may result in being banned from further commenting.
These terms and conditions are subject to change at any time and without notice.