Equipment information
Ameritec 30-0056 Interface
Manufacturer:
Image 1 of 1
If you have any other photos or manuals for the
Ameritec 30-0056 you can upload the files here .
Model:
30-0056
Date:
2000
Category:
Group:
Description:
AM8e E&M Adapter
Information
The Model 300056 AM8e E&M Adapter is physically designed to
replace the front
cover of the Call Analyzer. The illustration on the cover of
this manual shows both
units as they would be set up for use.
Note: F or brevity, the Model 300056 AM8e E&M Signaling
Adapter will be referred
to as the "E&M Adapter".
The E&M Adapter is electrically connected to the Call
Analyzer via a ribbon cable
from a "TO AM8e" connector on its front panel to the
LINE/TIMS connector on the
rear panel of the Call Analyzer. All power and PCM2 input
and output connections
between the E&M Adapter and the Call Analyzer are via this
connector.
The interfaces between the E&M signaling and VF circuits are
via bantam jacks on
the front panel of the E&M Adapter.
Functionally, the E&M Adapter is an Analog to
Digital/Digital to Analog signal
converter, which converts an E&M Signal from its line or
equipment Interface at a
Central Office, to 2.048Mbps PCM Rx and Tx Signals, which
are processed by the
Call Analyzer. This allows the Call Analyzer to Emulate or
Monitor either the
near-end (Tx) or far-end (Rx) signaling on an E&M Interface.
The user must select
PCM2 as PCM input.
Manual Type:
User Manual
Pages:
30
Size:
994.92 Kbytes (1018795 Bytes)
Language:
english
Revision:
C
Manual-ID:
18-0044
Date:
2000 10 18
Quality:
Electronic document, no scan, very well readable.
Upload date:
2017 10 14
MD5:
3bd77d2cc970418d5f63db1c329f83b5
Downloads:
423
Information
This manual is intended for use with the Ameritec Model
300056 AM8e E&M
Adapter (P/N 300056). This manual should be used in
conjunction with the AM8e
PCM/VF Call Analyzer Instruction Manual (P/N 180035), and
the AM8e Protocol Table
Development Guide (P/N 180040).
This manual is divided into 4 major sections, as listed in
the Table of Contents.
This first introductory section provides an overview of the
AM8e VF Call Analyzer,
AM8e E&M Signaling Adapter, and Protocol Table Development
Guide; all of which are
of fundamental importance to the instructions in this manual.
The second section describes the Model 300056 AM8e E&M
Adapter, its front panel,
and connections.
The third section is an overview of the characteristics of
the various E&M
connections and signaling types.
1.
INTRODUCTION ... 1
1.1 Ameritec AM8e PCM/VF Call Analyzer
... 1
1.2 AM8e Model 300056 E&M Adapter
... 2
1.3 AM8e Protocol Table Development Guide and
Disk ... 2
1.4 Overview of E&M Test Configuration
... 3
2. OPERATION OF THE E&M ADAPTER
... 4
2.1 Front Panel Controls and
Indicators ... 4
2.1.1 PWR ON/OFF (Power ON/OFF
Switch) ... 5
2.1.2 MODE (Mode Selector Switch)
... 5
2.1.3 MODE Indicators (Mode-Selected Indicators)
... 5
2.1.4 TYPE (E&M Type-Select Switch)
... 5
2.1.5 TYPE Indicators (E&M Type Indicators)
... 5
2.1.6 CONNECTION (Connection-Type Switch)
... 6
2.1.7 CONNECTION Indicators (Connection-Type Indicators)
... 6
2.1.8 E1/M1, and E2/M2 Indicators (Active Status of E&M
Signals) ... 6
2.2 Connection to the Call
Analyzer ... 6
2.2.1 TO AM8e (AM8e Interface
Connection) ... 6
2.3 Connections to Test
Leads ... 7
2.3.1 SB/SG Connection
... 8
2.3.2 Tx/Rx for
E1/M1 ... 8
2.3.3 Tx/Rx for
E2/M2 ... 9
2.3.4 A1/B1 VF Connector
... 9
2.3.5 A2/B2 VF Connector
... 9
2.3.6 CO Ground
Terminal ... 9
2.4 Setting the Operating Conditions
...
10
2.5 Remote Control of E&M
Adapter ...
12
2.5.1 Remote Setup (ADP
Command) ...
12
2.5.2 Remote Status (RADP Command)
...
13
2.6 Call Analyzer Display and Bit Indicators
...
13
3. E&M SIGNALING DESCRIPTION
...
14
3.1 Connection Types
...
15
3.1.1 2-wire E&M
...
16
3.1.2 4-wire E&M
...
16
3.1.3 4-wire E&M2
...
16
3.1.4 Phantom E&M
...
16
3.2 E&M Trunk
Types ...
18
3.2.1 E&M TYPE I
...
18
3.2.2 E&M TYPE II
...
18
3.2.3 E&M TYPE III
...
19
3.2.4 E&M TYPE
IV ...
20
3.2.5 E&M TYPE
V ...
20
APPENDIX
A ...
22
A.1 Analog R2 Monitoring in
AM8e ...
22
