Geräte Informationen

Electronic Navigation Industries 325LA Verstärker
Hersteller:
Electronic Navigation Industries
Modell: 325LA
Datum: 1988
Kategorie: Funk und Kommunikation
Gruppe: Verstärker
Beschreibung: BROADBAND POWER AMPLIFIER
Informationen:

The ENI Model 325LA is an all solid state Amplifier which has a flat frequency response from 250 kHz to 150 MHz. It provides up to 25W of linear power with low harmonic and intermodulation distortion. Gain is 50 dB nominal, with variation of less than +1.5 dB over the entire frequency range. Input and output impedance are 50Ω and the unit may be driven to full power output by most RF synthesizers, signal generators and swept signal sources. The ENI Model 325LA will deliver its rated power output into any load impedance, regardless of match. Built-in protection circuitry will absorb the power reflected from a mismatched load without causing failure or oscillation. Output RF voltage is displayed on the front panel meter. The Model 325LA is packaged for bench mounting and is shipping with rack mounting adapters. Its integral Power Supply and cooling operate from a 115 or 230 VAC 50/60 Hz main supply. The Model 325LA will raise the power level of signal sources and generators without requiring tuning or bandswitching. The Class A linear circuitry will amplify signals of AM, FM, SSB, TV and complex modulations limited only by their peak input and bandwidth, with minimum distortion.

Folgende Handbücher sind hierfür verfügbar:

Dokumenttyp: Service- und Bedienungsanleitung ENI-7566-Manual-Page-1-Picture
Seitenanzahl: 54
Dateigröße: 1.36 Mbytes (1423993 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer:
Datum: 1988
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: 68e1b2c4c0caa9460e5fd43b156f23d1
Downloads: 120 seit dem 25 Januar 2016
Informationen:

Chapter 1 Introduction 3 1.1 Introduction 3 1.2 Specifications 4 1.3 Instrument Identification 4 Chapter 2 Preparation For Use 5 2.1 Initial inspection 5 2.2 Claim for Damage 5 2.3 Main Voltage Setting 6 2.4 Mains Fuse Rating 6 2.5 Rack Installation 7 2.6 Power Cable Ground Protection 7 2.7 Cooling 7 Chapter 3 Operation 9 3.1 Funtional Description 9 3.2 Control, Indicators and Connectors 10 3.3 Operating Procedure 11 3.4 Precautions 12 Chapter 4 Maintenance 13 4.1 Initial Check 13 4.2 Gain and Gain Variation 13 4.3 RF Ouput Power Test 15 4.4 RF Output Distortion Test 16 4.5 Troubleshooting 17 4.6 Maintenance 18 Chapter 5 Figures 19 Figure 1 325LA Specifications 21 Figure 2 Front and Rear View 23 Figure 3 Gain and Gain Variation Test Set-Up 25 Figure 4 RF Output Power Test Set-Up 27 Figure 5 RF Power Distortion Test 29 Figure 6 Outline Drawings and Parts List 31 A. Driver Amplifier Board (325LA-14512) 33 B. RF Voltmeter Board (325LA-14513) 37 C. Power Amplifier Board (325LA-14515) 39 D. PS/Series Regulator Board(325LA-14516) 43 E. Other Parts 45 Figure 7 Glossary of Abbreviations 47 Reference Chart Reference 1 Schematics

ENI-7566-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image
Powered by Commentics