Информация по оборудованию

Philips PM 3585/90 Логический анализатор
Производитель:
Philips
Модель: PM 3585/90
Дата:
Категория: Измерительная техника
Группа: Логический анализатор
Описание:
Информация:
                                    The PM 3580/PM 3585 family of logic analyzers are State and
Timing Logic Analyzers for use within the R & D,
Manufacturing, Service and Education environments. They are
available in 32/64/96 channel models. The operating speed of
the PM 3580 is 100 MHz and the operating speed of the PM
3585 is 200 MHz.
The PM 3580 and the PM 3585 each come in two basic models,
these are:
PM 3580/30 32 dual analysis channels with 100 MHz Timing, 50
MHz state and 1K deep acquisition memory.
PM 3580/60 64 dual analysis channels with 100 MHz Timing, 50
MHz state and 1K deep acquisition memory.
PM 3585/60 64 dual analysis channels with 200 MHz Timing, 50
MHz state and 2K deep acquisition memory.
PM 3585/90 96 dual analysis channels with 200 MHz Timing, 50
MHz state and 2K deep acquisition memory.
All of the above models have the following standard features:
Human interface of an integral keypad and rotary knob, and a
nine inch white phosphor, high resolution CRT.
3.5 inch micro floppy disc drive for setup, storage and
retrieval of data.
Rear mounted BNC connections for input and output of trigger
signals.
External video port.
Centronics printer interface.
RS-232-C ports for other peripherals to be connected, e.g. a
printer.
W
Data acquisition is via any or all of the six inputs on the
front of the unit.
The system assembly board centres on the 68070 16/32 bit
CPU. It is accompanied by powerful data acquisition ASIC’s
that analyze the data received from the target system. An
interface is used to ensure that the acquisition system is
fully compatible with that of the CPU architecture. The
system assembly board also contains the circuitry required
to interface with the keyboard, disk drive, the CRT and the
output ports.

Эти руководства доступны для вышеуказанного оборудования:

Ручной тип: Обслуживание и Руководство пользователя Philips-8647-Manual-Page-1-Picture
Страниц: 187
Размер: 30.54 Mbytes (32022543 Bytes)
Язык: английский
Редакция:
Руководство ID/номер:
Дата:
Качество: Отсканированы документу, все читается.
Дата загрузки:
MD5: fa301b050b83b8232147d4f574f89df8
Загрузки: 134 начиная с 30 Январь 2017
Информация:
This manual contains all the information for completing
installation, maintenance, calibration and servicing on the
Logic Analyzers in the PM 3580/PM 3585 series.


I. GENERAL
..............................................................................................................................
1
1.1 GENERAL
INFORMATION......................................................................................
I
1.2 GUARANTEE STATEMENT
....................................................................................
ii
1.3 SAFETY
INSTRUCTIONS...........................................................................................iii
1.4 IMPAIRED SAFETY PROTECTION
.......................................................................
iv
1.5 GENERAL CLAUSES
..............................................................................................
iv
1.
INTRODUCTION...................................................................................................................
1
1.1 SYSTEM
CONFIGURATION....................................................................................
2
1.2 PERIPHERAL EQUIPMENT
....................................................................................
3
2. INSTALLATION AND
DISMANTLING.................................................................................
1
2.1 GENERAL
INFORMATION......................................................................................
2
2.1.1 SAFETY
NOTICE.........................................................................................
2
2.1.2 REQUIRED TOOLS AND MATERIALS
................................................... 3
2.2 MAINS VOLTAGE
SETTING....................................................................................
4
2.3 ACCESS TO
PARTS................................................................................................
5
2.3.1 REAR ACCESS
PLATE...............................................................................
5
2.3.2 INSTRUMENT
SLEEVE...............................................................................
6
2.3.3
HANDLE........................................................................................................
7
2.3.4 DISK DRIVE ASSEMBLY
..........................................................................
8
2.3.5 KEYBOARD
ASSEMBLY............................................................................
9
2.3.6 MAIN BOARD ASSEMBLY
.....................................................................
10
2.3.7 POWER SUPPLY UNIT
ASSEMBLY..................................................... 11
2.3.8 FAN UNIT
ASSEMBLY............................................................................
12
2.3.9 VISUAL DISPLAY UNIT
ASSEMBLY..................................................... 13
3.
MAINFRAME...........................................................................................................................
1
3.1 GENERAL
INTRODUCTION....................................................................................
2
3.2 POWER SUPPLY
.....................................................................................................
3
3.2.1 Block Diagram
description.......................................................................
4
3.2.2 Circuit
description......................................................................................
7
3.3 FLOPPY DISK
DRIVE...........................................................................................
13
3.3.1 Drive Performance
Specifications........................................................
13
3.3.2 Drive
Reliability.........................................................................................
13
3.3.3 Electronic Circuitry
.................................................................................
13
3.3.4 Setting the jumpers on a replacement floppy drive
....................... 15
3.4
KEYBOARD.............................................................................................................
18
3.5 VIDEO
MONITOR...................................................................................................
21
3.5.1 General
information.................................................................................
21
3.5.2 Circuit
description.......................................................
....................... 21
3.6 FAN
UNIT...............................................................................................................
25
3.7 MAIN-BOARD HARDWARE DESCRIPTION
..................................................... 25
3.7.1 General structure
main-board...............................................................
25
3.7.2 The different boards
...............................................................................
26
3.7.3 The CPU
section......................................................................................
29
3.7.4 Data Acquisition section
.......................................................................
48
4. VARIOUS ADJUSTMENTS AND JUMPER SETTINGS
.................................................. 1
4.1 GENERAL
INFORMATION......................................................................................
2
4.2 ADJUSTMENT
PROCEDURES..............................................................................
3
4.2.1 POWER SUPPLY
ADJUSTMENT.............................................................
3
4.2.2 POWER SUPPLY CHECKING
..................................................................
6
4.2.3 ADJUSTMENT OF THE
MONITOR..........................................................
7
4.2.4 ADJUSTMENT OF THE REAL TIME
CLOCK...................................... 11
4.3 JUMPERS AND
CONNECTORS.........................................................................
12
4.3.1 JUMPER
SETTINGS.................................................................................
13
5. ADAPTORS
...........................................................................................................................
1
5.1
INTRODUCTION.......................................................................................................
2
5.1.1 TIMING
ADAPTORS...................................................................................
2
5.1.2 MICROPROCESSOR ADAPTORS
.......................................................... 3
5.1.3 OVERALL SIGNAL PATH
.........................................................................
3
5.2. SERVICING THE
ADAPTORS.................................................................................
4
5.3. CURRENTLY SUPPORTED ADAPTORS
............................................................. 6
6. DIAGNOSTIC TESTS
.............................................................................................
1
6.1 GENERAL
INFORMATION......................................................................................
2
6.1.1 TEST
EQUIPMENT......................................................................................
3
6.2 POWER ON SELF
TEST........................................................................................
3
6.2.1
GENERAL.....................................................................................................
3
6.2.2 STACK TEST
.............................................................................................
3
6.2.3 ROM
TEST..................................................................................................
4
6.2.4 RAM
TEST..................................................................................................
4
6.2.5 FLOPPY CONTROLLER
TEST..................................................................
4
6.2.6 MULTI FUNCTION PERIPHERAL
(MFP)................................................ 4
6.3 DIAGNOSTIC TEST
DISKETTE..............................................................................
4
6.3.1 RAM
TEST..................................................................................................
6
6.3.2 CHECK-SUM EPROM’S
............................................................................
7
6.3.3 VIDEO CONTROLLER TEST (VSC)
........................................................ 8
6.3.4 68070 TIMER
TEST...................................................................................
9
6.3.5 KEYBOARD TEST
......................................................................................
9
6.3.6 RS-232 CONNECTOR
............................................................................
10
6.3.7 CENTRONICS TEST
..............................................................................
10
6.3.8 FLOPPY CONTROLLER
.........................................................................
12
6.3.9 SET DATE AND TIME
............................................................................
13
6.3.10 MULTI-FUNCTION PERIPHERAL (MFP)
............................................. 13
6.3.11 LOGIC
TARGET........................................................................................
13
6.4 BOUNDARY SCAN TEST
;...................................................................................
14
6.4.1 GENERAL
INFORMATION.......................................................................
14
6.4.2 ERROR
REPORTS...................................................................................
19
6.4.3 ERROR DEFINITIONS
............................................................................
20
6.4.4. EXPLANATIONS OF ERROR
REPORTS.............................................. 21
7. CORRECTIVE
MAINTENANCE..............................................................................
1
7.1
REPLACEMENTS.....................................................................................................
2
7.1.1 STANDARD
PARTS....................................................................................
2
7.1.2 SPECIAL
PARTS........................................................................................
2
7.1.3 TRANSISTORS AND INTEGRATED CIRCUITS
.................................... 2
7.1.4 STATIC SENSITIVE
COMPONENTS........................................................
3
7.2 SOLDERING
TECHNIQUES...................................................................................
4
7.2.1 SEMICONDUCTORS
.................................................................................
4
7.2.2 MICRO-MINIATURE
SEMICONDUCTORS.............................................. 5
7.2.3
ASIC’s..........................................................................................................
5
7.3 RE-CALIBRATION AFTER
REPAIR.......................................................................
9
8. SPECIFICATION
....................................................................................................................
1
8.1 GENERAL CHARACTERISTICS
............................................................................
3
8.1.1 DIMENSIONS
..............................................................................................
3
8.1.2.
WEIGHT........................................................................................................
3
8.1.3
DISPLAY........................................................................................................
3
8.1.4. POWER
........................................................................................................
3
8.2 ENVIRONMENTAL DATA
.........................................................................
3
8.2.1
STANDARDS................................................................................................
3
8.2.2
TEMPERATURE...........................................................................................
3
8.2.3 RELATIVE
HUMIDITY.................................................................................
3
8.2.4
ALTITUDE.....................................................................................................
4
8.2.5
VIBRATION...................................................................................................
4
8.2.6 EMI
...............................................................................................................
4
8.2.7 SAFETY
........................................................................................................
4
8.3 INPUT SECTION ..........
......................................................................................
4
8.4
CONFIGURATIONS...................................................................................................
5
8.4.1 TIMING ANALYZER
....................................................................................
5
8.4.2 GLITCH
ANALYZER....................................................................................
5
8.4.3 STATE
ANALYZER......................................................................................
6
8.5 DATA MEMORY STORAGE
MODES.....................................................................
7
8.6 TRIGGER SEQUENCER
.........................................................................................
8
8.6.1 TRIGGER RECOGNIZER’S
.......................................................................
9
8.6.2 TIME-OUT
COUNTER...............................................................................
10
8.6.3 TRIGGER POSITIONS
............................................................................
10
8.6.4 EXTERNAL
TRIGGERING.......................................................................
10
8.6.5 SELECTIVE STATE STORAGE
............................................................. 11
8.7 ACQUISITION
FUNCTIONS.................................................................................
11
8.8 LOGIC
PROBING...................................................................................................
12
8.9 LABEL FORMATTING AND ATTRIBUTES
........................................................ 12
8.10 DATA DISPLAY
.....................................................................................................
12
8.11 DATA/SETTING STORAGE
.................................................................................
13
8.12 HARD-COPY
OUTPUT...........................................................................................
13
8.13 EXTERNAL VIDEO OUTPUT
...............................................................................
14
8.14 EXTERNAL BNC TRIGGER
.................................................................................
14
8.15 EXTERNAL BNC TRIGGER OUT
.......................................................................
14
9. SPARE
PARTS.......................................................................................................................
1
9.1 UNITS &
ASSEMBLIES...........................................................................................
2
9.2 MAIN BOARD
PARTS.............................................................................................
3
9.2.1
ASIC’s..........................................................................................................
3
9.2.2 INTEGRATED
CIRCUITS............................................................................
3
9.2.3 XTALS
..........................................................................................................
4
9.2.4
SEMI-CONDUCTORS.................................................................................
4
9.2.5 CAPACITORS
.............................................................................................
4
9.2.6 RESISTORS
................................................................................................
5
9.2.7 CONNECTORS
...........................................................................................
6
9.2.8
MISCELLANEOUS......................................................................................
6
9.3
MONITOR..................................................................................................................
7
9.3.1 CONTROL BOARD
PARTS.......................................................................
7
9.3.2 CRT BOARD PARTS
.................................................................................
9
9.4 POWER SUPPLY PARTS
.........................................................................
9
9.5 KEYBOARD UNIT
PARTS.......................................................................
10
9.6 GENERAL PARTS
....................................................................................
10
9.7
ADAPTORS................................................................................................
11
9.8 TEST
EQUIPMENT...................................................................................
11
INDEX
.................................................................................................................................................
1
Philips-8647-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image
Powered by Commentics