Equipment information

BK Precision 1730 Power supply
Manufacturer:
Model:
1730
Date:
Category:
Group:
Description:
DC POWER SUPPLY 0-3A

Information

The B+K Precision Model 1710 and 1730 DC Power Supplies are high quality, general purpose dc power sources. The two models are very similar to each other, and both are covered in this instruction manual. Each of these power supplies provides 0-30 volts dc output, adjustable with both coarse and fine controls for precise settability. The current output of the Model 1710 is 0-1 amp, while Model 1730 is 0-3 amps. Two current ranges, High and Low, provide excellent current settability and meter resolution. Two large panel-mounted meters continuously monitor the output voltage and current. These power supplies exhibit excellent regulation and low ripple characteristics. The circuit design incorporates a pre-regulator, which greatly reduces internal power dissipation at low output voltages. The styling is both attractive and functional. The mechanical configuration conserves bench space and allows for easy portability. These instruments may be used in constant voltage or constant current applications. The crossover from constant voltage to constant current modes is smooth and automatic. LED’s indicate the “CV” (constant voltage) or “CC” (constant current) mode of operation. In constant voltage applications, a current limit may be preset. When load variations cause the current to reach the preset limit, the unit then regulates output current rather than output voltage. Current limits are adjustable from 5% to 100% of maximum. In constant current applications, the maximum voltage may be preset. When load variations cause current to drop below the regulated value, the unit reverts to regulated voltage operation at the preset value. Reverse polarity protection prevents accidental damage to the Power supply from improper connection to an external voltage, and current limiting protects the equipment being powered, as well as the Power supply. The output is isolated from chassis and earth ground, which permits full flexibility of connections. When needed, the (+) or (-) polarity may be strapped to ground, or either polarity may be floated to an external voltage. Two supplies may be connected in series as a0-to-60 volt power source, or two supplies may be connected in parallel, with suitable balancing resistors, for up to twice the output current. These power supplies are well suited for a wide variety of electrical and electronics applications, including service shops, engineering labs, production testing, school laboratories, and home use by hobbyists. 0-30 VOLTS Continuously variable over 0-to-30 volt range with coarse and fine controls. 0-1 AMP AND 0-3 AMP VERSIONS 0-to-l amp (1710) and 0-to-3 amp (1730) models available. Each rated for continuous duty at full output current. LABORATORY QUALITY Excellent regulation, low ripple. CONSTANT VOLTAGE OR CONSTANT CURRENT Provides regulated dc voltage output or regulated dc current output. Crossover is smooth and automatic. TWO CURRENT RANGES High-Low switch selects full output (0-1 A for Model 1710,0-3 A for Model 1730), or partial output (0-.25 A for Model 1710, and 0-.5 A for Model 1730). Low range improves current settability and meter resolution at lower current values. Switch simultaneously selects range of adjustment and corresponding meter scale. BUILT-IN METERING Two large, easy-to-read meters continuously monitor output voltage and current. LED INDICATORS Act as pilot light and identify mode of operation. PRE-REGULATOR Limits internal dissipation for higher reliability. ISOLATED OUTPUT Either polarity may be floated or grounded. OVERLOAD PROTECTION Fully adjustable current limiting (from 5% to 100% of maximum output current) protects circuit under test and the power supply. REVERSE POLARITY PROTECTION Prevents damage to Power supply from external voltage of reverse polarity. STYLING Modem functional styling. Configuration conserves bench space and aids portability. Logical, convenient layout of controls.

show more

User Manual
Manual Type:
User Manual
Pages:
27
Size:
1.13 Mbytes (1186014 Bytes)
Language:
english
Revision:
Manual-ID:
Date:
Quality:
Scanned document, all readable.
Upload date:
2017 01 24
MD5:
be3d2ebcd2cab264d25433162b6c47cd
Downloads:
1204

Information

TEST INSTRUMENT SAFETY ... inside front cover INTRODUCTION ... 3 FEATURES ... 4 SPECIFICATIONS ... 5 CONTROLS AND INDICATORS ... 7 OPERATING INSTRUCTIONS ... 9 Safety Precautions ... 9 Equipment Precautions ... 9 Hook-Up ... 9 Typical Constant Voltage Operation ... 12 Setting Current Limit ... 13 Typical Constant Current Operation ... 14 Constant Voltage/Constant Current Characteristic ... 15 Connecting Two Power Supplies in Series ... 15 Connecting Two Power Supplies in Parallel ... 18 Page APPLICATIONS ... 19 General ... 19 Electronics Servicing ... 19 Electronics Manufacturing ... 19 Electronics Design Lab ... 20 Electronics Education ... 20 Battery Charging ... 20 MAINTENANCE ... 21 Fuse Replacement ... 21 line Voltage Conversion, International Units ... 21 1710/1730 Calibration ... 23 Instrument Repair Service ... 23 WARRANTY SERVICE INSTRUCTIONS ... 27 LIMITED TWO YEAR WARRANTY ... 28

show more