Equipment information

Huntron Instruments 2000 Test Set
Manufacturer:
Model:
2000
Date:
1984
Category:
Group:
Description:
Tracker

Information

The Huntron Tracker 2000, is a versatile troubleshooting tool having the following' features: . Multiple test signal frequencies (50/60 Hz, 400 Hz, 2000 Hz). • Four impedance ranges (low, medium. 1, medium 2, high). • Automatic range scanning. • Range control: High. Lockout. • Rate of channel alternation and/or range scanning is adjustable. • Dual polarity pulse Generator for dynamic testing of three terminal devices. . LED indicators for all functions. . Dual channel capability for easy comparison. • Large CRT display yith easy to operate controls. The Tracker 2000 is a general purpose troubleshooting test instrument. It qualitatively evaluates digital, analog, and hybrid semiconductor devices, as well as capacitive and inductive devices, in or out of circuit, in a power off state. The Tracker 2000 operates by providing an ac stimulus to the component or circuit under test and displaying the resultant current and voltage levels and their phase relationship. The Tracker 2000 display indicates any component leakage, shorts, opens, noise, plus any combination of these problems caused by physical flaws. Table 1-1 lists the specifications of the Tracker 2000» Included with each Tracker 2000 is a set of Huntron Microprobe test leads. These test leads plug into the front panel test jacks of the Tracker 2000 and have special tips that allow contact with very small component terminals and printed circuit board traces without the danger of touching adjacent component leads and terminals. Also included with the Tracker 2000 are two blue microclips, a power /clock cable, and a special common test lead that allows the connection of Tracker 2000 common to two components. This test lead is used in the alternate mode of operation,

show more

User Manual
Manual Type:
User Manual
Pages:
188
Size:
5.34 Mbytes (5604174 Bytes)
Language:
english
Revision:
Manual-ID:
21-1045
Date:
Quality:
Scanned document, reading partly badly, partly not readable.
Upload date:
2014 03 11
MD5:
9176d14506f35dd883c00a7deeb25125
Downloads:
1368

Information

1.1 ABOUT THIS MANUAL This manual is provided for the operator of the Huntron Tracker 2000, The information contained within this manual familiarizes the reader first with the Tracker 2000 and its principles of operation, and then with its specific uses. A working knowledge of the Tracker 2000’s operating principles greatly assists the user in evaluating the Tracker 20005s display, especially when using the instrument for troubleshooting purposes. This manual is divided into sections. Each section contains information pertinent to a certain application of the Tracker 2000. The sections contain the following information; SECTION 1 GENERAL INFORMATION This section provides a description of the Tracker 2000 and lists its specifications. It also describes the principles on which the Tracker 2000 operates* using a pure resistance and a diode as examples, SECTION 2 OPERATING INSTRUCTIONS This section describes the controls and indicators of the Tracker 2000, It also describes the Tracker 2000’s comparative testing feature. SECTION 3 TESTING DIODES This section describes the characteristics of the diode (showing its voltage to current relationship), which is essential to understanding the Tracker 2000 display. This section also illustrates and describes Tracker 2000 signatures produced when the test leads are connected to (or across) circuits containing the following devices: silicon diodes, high voltage silicon diodes, zener diodes, and light-emitting diodes. SECTION 4 TESTING TRANSISTORS This section illustrates and describes Tracker 2000 signatures produced when the test leads are connected to (or across) circuits containing the following devices: NPN and PNP transistors, Darlington pairs, germanium transistors5 MOSFETs and JFETs. SECTION 5 RESISTORS, CAPACITORS, AND INDUCTORS This section describes and illustrates Tracker 2000 signatures produced when the test leads are connected to capacitive, inductive, and resistive circuits or devices. SECTION 8 TESTING MULTIPLE COMPONENT CIRCUITS This section covers the testing of diode/resistor combinations, diode/capacitor combinations, resistor/ capacitor combinations, and inductor/diode combinations. SECTION 7 TESTING INTEGRATED CIRCUITS This section discusses integrated circuit technology followed by testing information for linear devices such as operational amplifiers and voltage regulators. Testing information is also provided for the LM555 Timer as well as TTL, LS TTL, and CMOS devices. SECTION 8 USING THE PULSE Generator This section describes the testing of controlled input devices using the pulse Generator. Testing information is provided for SCR and TR1AC devices as well as various optocouplers. SECTION 9 TESTING COMPONENTS BY COMPARISON This section provides Tracker 2000 signatures for defective devices as compared to known good devices. The Tracker 2000 is used in the alternate mode to check a power transistor, a high voltage diode, and an electrolytic capacitor. SECTfON 10 SOLVING BUS PROBLEMS This section contains information that may be helpful when attempting to isolate faults caused by defective devices connected to a common bus. SECTION 11 TROUBLESHOOTING TIPS This section contains a series of troubleshooting suggestions and information that should assist the user when using the Tracker 2000. APPENDIXES A. MT'L TRACKER TESTS B. COMPONENT CONCEPTS TRACKER TESTS

show more

Service and User Manual
Manual Type:
Service and User Manual
Pages:
198
Size:
5.49 Mbytes (5754922 Bytes)
Language:
english
Revision:
6
Manual-ID:
21-1052
Date:
Quality:
Scanned document, reading partly badly, partly not readable.
Upload date:
2014 03 11
MD5:
abca529fece61a5d6edc9daa2bf09fad
Downloads:
2341