Equipment information

Ameritec 30-0056 Interface
Manufacturer:
Model:
30-0056
Date:
2000
Category:
Group:
Description:
AM8e E&M Adapter

Information

The Model 300056 AM8e E&M Adapter is physically designed to replace the front cover of the Call Analyzer. The illustration on the cover of this manual shows both units as they would be set up for use. Note: F or brevity, the Model 300056 AM8e E&M Signaling Adapter will be referred to as the "E&M Adapter". The E&M Adapter is electrically connected to the Call Analyzer via a ribbon cable from a "TO AM8e" connector on its front panel to the LINE/TIMS connector on the rear panel of the Call Analyzer. All power and PCM2 input and output connections between the E&M Adapter and the Call Analyzer are via this connector. The interfaces between the E&M signaling and VF circuits are via bantam jacks on the front panel of the E&M Adapter. Functionally, the E&M Adapter is an Analog to Digital/Digital to Analog signal converter, which converts an E&M Signal from its line or equipment Interface at a Central Office, to 2.048Mbps PCM Rx and Tx Signals, which are processed by the Call Analyzer. This allows the Call Analyzer to Emulate or Monitor either the near-end (Tx) or far-end (Rx) signaling on an E&M Interface. The user must select PCM2 as PCM input.

show more

User Manual
Manual Type:
User Manual
Pages:
30
Size:
994.92 Kbytes (1018795 Bytes)
Language:
english
Revision:
C
Manual-ID:
18-0044
Date:
2000 10 18
Quality:
Electronic document, no scan, very well readable.
Upload date:
2017 10 14
MD5:
3bd77d2cc970418d5f63db1c329f83b5
Downloads:
451

Information

This manual is intended for use with the Ameritec Model 300056 AM8e E&M Adapter (P/N 300056). This manual should be used in conjunction with the AM8e PCM/VF Call Analyzer Instruction Manual (P/N 180035), and the AM8e Protocol Table Development Guide (P/N 180040). This manual is divided into 4 major sections, as listed in the Table of Contents. This first introductory section provides an overview of the AM8e VF Call Analyzer, AM8e E&M Signaling Adapter, and Protocol Table Development Guide; all of which are of fundamental importance to the instructions in this manual. The second section describes the Model 300056 AM8e E&M Adapter, its front panel, and connections. The third section is an overview of the characteristics of the various E&M connections and signaling types. 1. INTRODUCTION ... 1 1.1 Ameritec AM8e PCM/VF Call Analyzer ... 1 1.2 AM8e Model 300056 E&M Adapter ... 2 1.3 AM8e Protocol Table Development Guide and Disk ... 2 1.4 Overview of E&M Test Configuration ... 3 2. OPERATION OF THE E&M ADAPTER ... 4 2.1 Front Panel Controls and Indicators ... 4 2.1.1 PWR ON/OFF (Power ON/OFF Switch) ... 5 2.1.2 MODE (Mode Selector Switch) ... 5 2.1.3 MODE Indicators (Mode-Selected Indicators) ... 5 2.1.4 TYPE (E&M Type-Select Switch) ... 5 2.1.5 TYPE Indicators (E&M Type Indicators) ... 5 2.1.6 CONNECTION (Connection-Type Switch) ... 6 2.1.7 CONNECTION Indicators (Connection-Type Indicators) ... 6 2.1.8 E1/M1, and E2/M2 Indicators (Active Status of E&M Signals) ... 6 2.2 Connection to the Call Analyzer ... 6 2.2.1 TO AM8e (AM8e Interface Connection) ... 6 2.3 Connections to Test Leads ... 7 2.3.1 SB/SG Connection ... 8 2.3.2 Tx/Rx for E1/M1 ... 8 2.3.3 Tx/Rx for E2/M2 ... 9 2.3.4 A1/B1 VF Connector ... 9 2.3.5 A2/B2 VF Connector ... 9 2.3.6 CO Ground Terminal ... 9 2.4 Setting the Operating Conditions ... 10 2.5 Remote Control of E&M Adapter ... 12 2.5.1 Remote Setup (ADP Command) ... 12 2.5.2 Remote Status (RADP Command) ... 13 2.6 Call Analyzer Display and Bit Indicators ... 13 3. E&M SIGNALING DESCRIPTION ... 14 3.1 Connection Types ... 15 3.1.1 2-wire E&M ... 16 3.1.2 4-wire E&M ... 16 3.1.3 4-wire E&M2 ... 16 3.1.4 Phantom E&M ... 16 3.2 E&M Trunk Types ... 18 3.2.1 E&M TYPE I ... 18 3.2.2 E&M TYPE II ... 18 3.2.3 E&M TYPE III ... 19 3.2.4 E&M TYPE IV ... 20 3.2.5 E&M TYPE V ... 20 APPENDIX A ... 22 A.1 Analog R2 Monitoring in AM8e ... 22

show more