Equipment information
IFR FM/AM-1600S Communications Service Monitor
Manufacturer:
Image 1 of 1
If you have any other photos or manuals for the
IFR FM/AM-1600S you can upload the files here .
Model:
FM/AM-1600S
Date:
1991
Category:
Group:
Description:
COMMUNICATIONS SERVICE MONITOR
Information
The FM/AM-1600S is a microprocessor controlled, digitally
synthesized communication service monitor which combines the
operations of many different test instruments into a single,
compact unit. Functions the FM/AM-1600S is capable of
performing include:
RF Generator Duplex
Spectrum Analyzer DMM
Distortion Meter Audio Frequency Meter RF Power Meter Signal
Strength Meter Phase Meter Tracking Generator Digital Radio
Paging Encode and Decode
Receiver AF Generator Oscilloscope Deviation (Peak) Meter
SINAD Meter Frequency Error Meter Modulation Meter Bit Error
Rate Meter Deviation (RMS) Meter Cable Fault Detector Analog
Radio Paging Encode and Decode
The FM/AM-1600S utilizes an alphanumeric keypad, dedicated
function keys, multitask Soft Function Keys and a
high-resolution color CRT to display, enter and edit
functions and data. Testing with this instrument can be done
remotely or manually. The FM/AM-1600S can perform tests from
pre-programmed setups or formats determined at the time of
the test.
Microprocessor controlled memory allows storage and recall
of parameters for each of the testing modes as well as
storage and recall of Oscilloscope and Spectrum Analyzer
traces for signal comparison.
The FM/AM-1600S is capable of generating modulated or
unmodulated carrier signals from 250 kHz to 999.9999 MHz (in
100 Hz steps). The output level is variable from -137 dBm to
0 dBm. Modulation types include AM, FM and PM. Modulation
can also be applied from an external source. The RF
Generator also functions as a tracking generator for swept
measurements or as an offset generator in Duplex Mode.
Metering functions available for this operation mode include
SINAD, DMM, Distortion and Audio Frequency Level meters. The
Oscilloscope and Spectrum Analyzer are also available for
use on the RF Generator Operation Screen.
1-3 Receiver
The FM/AM-1600S is capable of receiving modulated and
unmodulated signals from 250 kHz to 999.9999 MHz (in 100 Hz
steps). The FM/AM-1600S receives AM, FM, PM, and SSB
modulated signals. Metering functions in the FM/AM-1600S
available with the Receiver include RF Power, Modulation,
Deviation, Distortion, Frequency Error, AF Frequency, Signal
Strength and SINAD meters and counters. The Oscilloscope and
Spectrum Analyzer are also available for use on the Receiver
Operation Screen. The FM/AM-1600S Receiver is capable of
executing user defined frequency scan operations as well as
single frequency operations. The Receiver accesses "off the
air" signals through the Antenna IN Connector or higher
powered signals are accessed through the T/R Connector.
Manual Type:
User Manual
Pages:
428
Size:
12.60 Mbytes (13216305 Bytes)
Language:
english
Revision:
1.10
Manual-ID:
1002-8600-000
Date:
Quality:
Scanned document, all readable.
Upload date:
2015 05 23
MD5:
154a1375e4ea7f9ae2d5989f9cd0d3ac
Downloads:
997
Information
This manual contains instructions for operating the
FM/AM-1600S Communications Service Monitor. The instruction
level is relatively basic and presupposes no previous
experience on the part of the operator with a communication
service monitor of this type. A basic understanding of
communication electronics and practical troubleshooting
methods is helpful. It is strongly recommended that the
operator be thoroughly familiar this manual before
attempting to operate the unit.
ORGANIZATION
The FM/AM-1600S Operation Manual is composed of the
following sections:
SECTION 1 - INTRODUCTION
Provides an introduction to the unit and a brief overview of
unit functions. Specifications are also included in this
section.
SECTION 2 - INSTALLATION
Provides a step-by-step procedure for placing the
FM/AM-1600S into operation.
SECTION 3 - DESCRIPTION OF CONTROLS, CONNECTORS AND INDICATORS
Identifies and functionally describes all FM/AM-1600S
controls, connectors and indicators. Additionally, all CRT
Operation Screens and Menus are identified and available
parameters listed and explained.
NOTE: As an operating aid, Figures 3-1 and 3-2, which locate
and identify all
FM/AM-1600S controls, connectors and indicators, are located
on a fold-out page. By extending the fold-out page, the
operator can reference any front or rear panel control while
simultaneously performing any operating procedure contained
elsewhere in the manual.
SECTION 4 - OPERATION
Contains instructions for operating the FM/AM-1600S Mode
Operating Screens and Menus, in addition, this section
contains a selection of basic operating procedures
pertaining to ail major functions of the set.
SECTION 5 - PERFORMANCE EVALUATION
identifies and explains procedures the operator can use to
insure the FM/AM-1600S is performing properly.
SECTION 6 - REMOTE OPERATION
Contains step-by-step procedures for configuring and
operating the FM/AM-1600S remotely. Lists unit specific
commands for remote operations as well as commands mandated
by IEEE 488.2 1987.
Manual Type:
User Manual
Pages:
478
Size:
14.44 Mbytes (15143113 Bytes)
Language:
english
Revision:
2
Manual-ID:
1002-8600-000
Date:
Quality:
Scanned document, all readable.
Upload date:
2014 01 20
MD5:
9dfc3c965ee43df58766d68fab3f9383
Downloads:
1823
Information
This manual contains instructions for operating the
FM/AM-1600S Communications Service Monitor. The instruction
level is relatively basic and presupposes no previous
experience on the part of the operator with a communication
service monitor of this type. A basic understanding of
communication electronics and practical troubleshooting
methods is helpful. It is strongly recommended that the
operator be thoroughly familiar this manual before
attempting to operate the unit.
ORGANIZATION
The FM/AM-1600S Operation Manual is composed of the
following sections:
SECTION 1 - INTRODUCTION
Provides an introduction to the unit and a brief overview of
unit functions. Specifications are also included in this
section.
SECTION 2 - INSTALLATION
Provides a step-by-step procedure for placing the
FM/AM-1600S into operation.
SECTION 3 - DESCRIPTION OF CONTROLS, CONNECTORS AND INDICATORS
Identifies and functionally describes all FM/AM-1600S
controls, connectors and indicators. Additionally, all CRT
Operation Screens and Menus are identified and available
parameters listed and explained.
NOTE: As an operating aid, Figures 3-1 and 3-2, which locate
and identify all
FM/AM-1600S controls, connectors and indicators, are located
on a fold-out page. By extending the fold-out page, the
operator can reference any front or rear panel control while
simultaneously performing any operating procedure contained
elsewhere in the manual.
SECTION 4 - OPERATION
Provides instructions for operating the FM/AM-1600S Mode
Operating Screens and Menus. In addition, this section
contains a selection of basic operating procedures
pertaining to all major functions of the Test Set.
SECTION 5 - PERFORMANCE EVALUATION
Identifies and explains procedures the operator can use to
insure the FM/AM-1600S is performing properly.
SECTION 6 - REMOTE OPERATION
Provides procedures for configuring and operating the
FM/AM-1600S remotely. Lists unit specific commands for
remote operations as well as commands mandated by IEEE 488.2
1987.