Geräte Informationen

Tektronix FG 504 Generator
Hersteller:
Tektronix
Modell: FG 504
Datum: 1979
Kategorie: Messgeräte
Gruppe: Generator
Beschreibung: 40MHz Function Generator
Informationen:
                                    Introduction

The FG 504 Function Generator provides low distortion sine,
square, triangle, ramp, and pulse waveforms over the
frequencies from 0.001 Hz to 40 MHz in ten decades. A
user-definable custom frequency range is also available. The
output amplitude is 10 mV to 30 V peak-to-peak into an open
circuit and 5 mV to 15 V peak-to-peak into a 50 Q load. The
output impedance is 50 Q. The FG 504 may be swept between
the START and STOP FREQ dial settings with a linear or
logarithmic sweep. The output may be phase locked, gated, or
triggered for single cycle output. The output waveform may
be shifted ±80° from the triggering waveform. The symmetry
of the output waveform may also be varied. For the slower
frequencies, the output may be held at any level by pushing
the front panel button labeled HOLD.
A voltage-controlled frequency (VCF) input controls the
output frequency from an external voltage source. The output
frequency can be swept above or below the selected
frequency, to a maximum of 1000:1, depending on the polarity
and amplitude of the VCF input and the selected output
frequency. Provision is also made for amplitude modulating
the sinewave output from an external source.
The variety of swept and modulated signals available from
the FG 504 make it especially useful for such applications
as testing amplifier or servo-system response, distortion,
and stability. It is useful for fm generation, as a beat
frequency oscillator, as a gated triggered or phase-locked
logic interface, or as a source for various ramp or pulse
waveforms. It is also useful as a source for amplitude
modulated signals for various purposes.

Folgende Handbücher sind hierfür verfügbar:

Tektronix -- FG 504 -- Service- und Bedienungsanleitung
Dateiname: Tektronix-8938-Manual-Page-1-Picture
Dokumenttyp: Service- und Bedienungsanleitung
Seitenanzahl: 178
Dateigröße: 15.83 Mbytes (16599429 Bytes)
Sprache: Englisch
Revision: revised
Dokument-ID/Nummer: 070-2655-00
Datum: 01 Mai 1982
Qualität: Gescanntes Dokument, alles ist lesbar.
Upload Datum:
MD5: d52495b12e1d4a86c0fa80492bf05d3b
Downloads: 14 seit dem 23 April 2017
Informationen:
LIST OF ILLUSTRATIONS ................ ii

LIST OF TABLES....................... iii

Section 1 SPECIFICATION............... 1-1

Section 2 OPERATING INSTRUCTIONS...... 2-1

English Version French Version German Version Japanese Version

WARNING

THE FOLLOWING SERVICE INSTRUCTIONS ARE FOR USE BY QUALIFIED
PERSONNEL ONLY. TO AVOID PERSONAL INJURY, DO NOT PERFORM ANY
SERVICING OTHER THAN THAT CONTAINED IN OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
Page

Section 3 THEORY OF OPERATION ........ 3-1

Section 4 CALIBRATION PROCEDURE...... 4-1

Performance Check........... 4-3

Adjustment Procedure ......... 4-8

Section 5	MAINTENANCE................ 5-1

Section 6	OPTIONS.................... 6-1

Section 7	REPLACEABLE ELECTRICAL PARTS 7-1

Section 8	DIAGRAMS AND ILLUSTRATIONS . . 8-1

Section 9	REPLACEABLE MECHANICAL PARTS 9-1
Tektronix-8938-Manual-Page-1-Picture
Kostenlos herunterladen


Kommentare

Noch keine Kommentare vorhanden.

Kommentar Hinzufügen

* Pflichtfeld
(wird nicht veröffentlicht)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
What is the day after Friday?
 
Die Antwort lautet:
 
Informiere mich via E-Mail über neue Kommentare.
 
Meine Daten auf diesem Computer.
 
 
Powered by Commentics